ICON is known as the original pioneer of this type of shoring system in the Country.  ICON’s slide rail shoring systems are MADE IN THE USA and out of high yield, Grade 50 steel.  Components of this modular steel shoring system are lineal panels or plates, rails or posts and bracing that enable the contractor to install 2, 3 and 4 sided pits and trenches to support a variety of excavations in many different soil conditions. ICON manufactures slide rails systems in either a single, double or a triple rail design with a choice of Roller Rail Bracing (Struts) or Fixed Position Bracing built for flexibility, durability, and with the contractor in mind.

What is a Slide Rail System? Slide rail systems a Modular Steel Shoring system that can be set up in an initial excavation (Pilot But) and then installed down as you dig.  The Slide Rail system an extremely versatile and alternative way to shore up pit and trench excavations using a dig and push method of installation rather than vibration to drive sheeting into the ground.

“Dig and Push” method of installation eliminates the need for vibratory hammers, increases production by 50% and decreases labor by 30% to 40% on average versus conventional sheeting.

Making use of Icon’s waler frames and utility panels allow you to sheet and shore around existing utilities and pipes.



ICON’s Slide Rail system can be utilized on excavations for:

  • Large and small sewer line
  • Large water mains
  • Tunnel access pits or shafts
  • Tank installations
  • Environmental remediation and cleanup
  • Large and small diameter vaults
  • Pump stations, lift stations, wet wells, manholes and junction boxes
  • Bridge footings and wing walls
  • And much, much more.

How do you install a Slide Rail System? ICON’s slide rail system is installed simultaneously as the trench or pit is excavated. Start by excavating the trench to 4 feet deep. Install the first rails and lining plates. Then square up the system as best you can. Continue to dig on the inside of the system removing the excavated material as needed. Add more panels and rails incrementally using the “dig and push” method until the required sub-grade is reached.

Installation of a pre-engineered modular system of panels, rails and braces allows the contractor to easily sheet a small or large pit 30% to 50% faster than conventional methods such as steel-driven sheet piling


Work in Tight Areas

  • Installation and excavation take place together decreasing your costs by 50%.
  • Minimal vibration during installation minimizes damage to adjacent utilities and surrounding buildings.
  • More working room wall-to-wall without the use of inside waler beams.

Sheet and Shore around Existing or Adjacent Utilities, Safely and Quickly

  • With the use of ICON’s internal and utility crossing frames, existing utilities can be easily sheeted around as you advance the system.
  • Vertical panels, overlapping sheeting or vertical wood can be inserted into the crossing frame to shore around the existing utility.

Remove cross braces when needed by tying back to large, wide-flange beams

  • Rebrace Pit designs are available up to 40’W x 62’L and a maximum of 20’ in depth.

Triple Slide Rail Systems are used for Large, Deep, Difficult Jobs

  • Built to last for even the largest and toughest soil conditions.
  • Sheet as deep as 36’ in C60 soil.
  • Provide up to a 15’ or larger working room clearance under the bottom brace.

Master Design:


ICON Equipment is proud to offer our customers and dealers the most exciting slide rail design anywhere in the world. Our Transformer slide rail system is our fourth generation in designs that we have improved on since we started manufacturing slide rail systems in the USA.

The Transformer design is 45% stronger than our past rail designs and unlike other systems on the market that only offer one type of bracing, the Transformer slide rail system combines the best of all bracing designs and offers these options on one great rail. Why should you spend money with other manufacturers on several different types of slide rails for your fleet when you can do everything and more with the Transformer slide rail from ICON?

Download a 2-D example drawing of the Transformer Slide Rail by CLICKING HERE.

Trench Application

PitApplicationcurvedPit Application

Bracing Designs:

Style 1: Roller Rail Bracing



Roller Rail Bracing will allow the contractor to move the bracing cart up and down the face of the Transformer rail when needed in order to provide large clearances for large pipes, culverts, structures or to perform an easier removal of the cross braces during a re-bracing procedure for open clear-span designs.

Style 2: Fixed Rail Bracing




Fixed Rail Bracing will allow the contractor to plan ahead before the start of an installation and pin the bracing into specific locations along the face of the Transformer rail based on the project requirements.  This ensures a proper assembly and perfect installation of the bracing every time.

Style 3: Angled Raker Bracing